Dealing with a Unexpected Hot Water System Failure: Essential Steps
Dealing with a Unexpected Hot Water System Failure: Essential Steps
Blog Article
They are making a few great pointers related to What Would Cause My Electric Water Heater to Stop Working? as a whole in this article further down.
![How to Troubleshoot and Repair an Electric Water Heater](https://www.maeser.com/wp-content/uploads/2019/07/water-heater-customer-1024x735.png)
Lots of contemporary houses use an electrical water heater for their heating unit, because of its benefit and ease of use. Nevertheless, much like any other electrical appliances, troubles might develop with its usage, unexpectedly. It can be really irritating to get up to a cold shower instead of a warm one or having your bathroom with water that isn't hot enough or perhaps as well hot. Whatever the case might be, hot water heater troubles can be fairly nerve-racking. Fortunately, we have actually made a listing of possible solutions to your hot water heater concerns. There are a variety of variables that can trigger most of these issues, maybe a problem with the power supply, the electric burner, or the thermostat. Before doing anything, ensure you switch off the primary power supply for security. Whatever the issue is, getting it taken care of must not posture excessive of a problem if you comply with these steps:
Check Your Power Supply:
As standard as this may appear, it is very required. Without adequate power, your hot water heater will not operate. So the first thing to do when your water instantly stops working is to confirm that it isn't a power issue. Inspect if the fuse is burnt out or the circuit breaker stumbled. If the circuit breaker is the problem, merely turn it off and on once again. Replace any broken or damaged fuse. Check the device with power after these adjustments to see if it's now functioning.
Examine the Heating Element in the Hot Water Heater:
If it's not a power problem, then attempt taking a look at your heating element if it is still functioning. Test each of your burner to make sure the trouble isn't with any one of them. If any one of them is malfunctioning, change that part and afterwards check whether the hot water is back on.
Inspect Your Thermostat:
If your water heater still isn't working or the water coming out isn't hot sufficient, you might require to check the temperature setups on your upper thermostat. Ensure the breaker is turned off before doing anything. Open the access panel and also press the red switch for temperature reset over the thermostat. This ought to assist heat the water. Turn the breaker back on and also inspect if the problem has actually been solved.
Call A Specialist:
If after replacing all damaged parts and also resetting your temperature level, the water heater still isn't working, you might need to call a professional plumber for a specialist viewpoint. The issue with your heating system could be that the cold and hot faucets have actually been changed or it may be undersized for the quantity of hot water needed in your home. Whatever the situation might be, a specialist plumber would certainly aid resolve the trouble.
Verdict
Hot water heater problems are not always significant. Much of them are due to minor problems like a blown fuse or worn-out burner. Replacing the damaged components need to suffice. Nonetheless, if you are still incapable to solve the problem, give a call to your closest plumber to come to get it repaired.
8 possible reasons why you have no Hot Water
Along with streaming Netflix and having light flood a room when we flick a switch, having hot water flow from our taps and showerheads whenever we want is an oft-overlooked modern miracle of homeownership. That's why, when that flow goes cold, it can be shocking — and not just in a "Wow, that's freezing" kind of way while you're in the shower.
Water Leak
Before hot water reaches your taps and showerheads, it needs to spend some time in your water heater. This appliance, which can be either gas- or electric-powered, takes the cold water that enters your home from your well or utility company and cooks it until it gets hot. It's akin to an electric tea kettle.
Obviously, if your water heater is leaking, it will never fill with water so it won't have anything to warm. To see if this is the case, simply examine the area around the water heater to see if it is wet. If so, you'll likely need to replace the unit, but you can also call in a pro for a second opinion and to see if it is fixable. Sometimes leaks can happen around fixtures on the water heater, and if so, the solution might be as simple as replacing them.
Gas Heater: Gas Leak
If your hot water is fueled by natural gas and there is a leak in the supply line or where the line enters the tank, the appliance won't have the power it needs to heat up your water. The result is not only inconvenient, but it can be extremely dangerous as well. If you smell gas when you investigate your water heater, call your gas utility company immediately and report it as an emergency. It might also be prudent to leave your home until a repair person from the company arrives. Your utility company will usually fix any kind of gas leak. However, in terms of getting your water heater working again, you'll need to relight the pilot and wait a while to see if it is functioning properly. You can call in a water heater specialist or plumber to help with this.
Gas Heater: Pilot Light Problems
There are two other issues with gas-powered water heaters that can lead to a loss of hot water. The first is a pilot light that's blown out. The pilot light is the source of a constant flame inside your water heater. When the heater determines the need to heat up the water it is holding, it will open a valve that will cause gas to flow over the pilot light and cause it to ignite. To see if your pilot light is functioning, there is usually a small window in the front of the water heater. If you can't see a flame, remove the access panel and see if that helps you locate it. If there is still no flame, you'll need to relight it in accordance with the manufacturer's instructions.
Your pilot light should burn with a bright blue flame. If not, make sure there are no drafts affecting it, which could keep it from functioning properly. If the flame looks yellow, it might be a sign of the presence of carbon monoxide, which spells trouble and needs to be looked at right away by a technician.
Gas Heater: Faulty Thermocouple
The second reason why a gas-powered water heater might fail is a faulty thermocouple. This is a small probe that should sit in the pilot light flame. Its purpose is to stop the flow of gas if it senses that the pilot light is out. Sometimes, these probes get knocked off track, so make sure it is directly in the flame. They can also get a buildup on them that prevents their function, so try cleaning yours off with some steel wool or fine-grit sandpaper. If your pilot light won't stay lit and you've tried these steps to fix the thermocouple, it is likely faulty and needs to be replaced. Call a technician.
Electric Heater: Breaker Blues
Electric water heaters don't have pilot lights, because there is no gas to burn in order to heat up the water. Instead, they do their magic through the use of (naturally) electricity. But that's not to say things can't go wrong with them. If your electric water heater isn't working properly, there's a good chance that a breaker was tripped that supplies the appliance power. Check your breaker box and flip any breakers that have switched to the off position back on. If it trips again, then there might be a fault in the water heater, and you'll want to call in a pro to have a look.
Electric Heater: Reaching The Limit
If the breaker is fine, check to see if the high-temperature limit has switched off on the water heater itself. To do so, first turn off the breaker to the unit. Then remove the service panel and press the red button you'll find there. This is the limit switch, and resetting it could solve your problem. To check, replace the panel, turn the breaker back on and listen to see if the water heater is functioning again.
Electric Heater: Heating Element
If these steps don't fix the issue, then you might have a failed heating element, which will need to be replaced. Unless you are comfortable with such repairs, calling in a technician might make the most sense.
https://www.homeserve.com/en-us/blog/home-improvement/no-water-heater/
![](http://blog.coldwellbanker.com/wp-content/uploads/2016/10/WH_Image1.jpg)
Hopefully you enjoyed reading our section about How to Troubleshoot and Repair an Electric Water Heater. Thank you so much for taking a few minutes to browse our blog post. So long as you liked our post if you please do not forget to pass it around. I praise you for your time. Visit again soon.
Stay calm, just ring. Report this page